In: GMC
28 Feb 2010Can some one give me the procedure for replacing the lower ball joints on a 99 gmc yukon 4wd. It has a torsion bar, do I have to loosen that or anything? The ball joints are the press in type. Also I have to grease the new ball joints, how do I know when it [...]
In: GMC
28 Feb 2010Is it 2 hours? 4 hours labor? plus parts…so that comes in around … what? $200? $350? more? Just a ball-park figure, please!!!
1997 Merc. Mtnr. V8, AWD. Front Drive shaft assembly does not match up to any assembly I have seen before. The front driveshaft seems to have half of the CV joint attached to it. Auto Parts stores do not know where to find a replacement. Any Thoughts?
In: Volvo
14 Feb 2010I removed all the bolts and everything but the ball joint is stuck in the lower arm. What is the easiest way to take it out?
i have very crappy instructions on how to replace the axel in the manual. but i have better instructions to replace halfshaft on autozone… the parts store only has the axel. maybe i can find the cv halfshaft somewhere?
In: Ford
13 Feb 2010i tried getting at it with a slide hammer and that didnt work
In: Ford
13 Feb 2010can a fouled cv joint cause front tire to lock up and cause car to stall and keep tranny from engageing??
In: Ford
13 Feb 2010The drive shaft is now off the car and in a vice with the outer cv joint still attached I can see a little movement but will still not knock off. Has any one worked on this model off car. any ideas.
cheers
In: Ford
13 Feb 2010I drove it in and now I am told it is in pieces and will not go back together.
Is it a 32mm?
In: Ford
13 Feb 2010I’m needing any info, diagram, walkthrough from a manual, etc. on CV joint removal & installation for a: 1991 Ford Tempo / AT / 2.3 liter engine. Any info would be appreciated. Thanks!
In: Honda
9 Feb 2010how do i know which one is my problem if tthey both sound alike?? i have a honda civic si 2003 and every time i passed a bump it sounds like it was one of those problems please help??
In: Honda
9 Feb 2010I need to get both replaced on my Honda Civic and wonder what the heck they are(can you tell I’m a girl, ha ha!)
In: Honda
9 Feb 2010i have a 2001 honda civic lx and the ball joint in the right front tire is popping out. I took it to the mechanic and they said that the spindle had to be changed. So i went and got one at a junk yard. They put it in, and told me to [...]
1983 honda civic.i just use it to drive small distances in a rural community but I do get up to 50km sometimes.It’s a great car..it just keeps going and going.Not very pretty though.Don’t really want to spend any more money on it.Is there a lot off danger here if it happens while driving at 50km
In: Honda
8 Feb 2010I undue the bottom ball joint and pull the strut out of the way and slide the cv joint out
In: Honda
8 Feb 2010The Drive Axle is the shaft from your front gearcase to your wheel. The Ball Joint is the part attached to the suspension links at the tip of the triangle it creates.
In: Honda
8 Feb 2010Just to make sure you dont make two trips, you need a ball-joint separator and a press. The press is a simple machine that as you can guess just presses the ball into the joint, the separator just wedges them apart. Both can be found at most autoparts stores for free, just a refundable deposit. [...]
In: Honda
8 Feb 2010my 1997 civic SIR hatch back failed the car test today the ball joint is worn on the front drivers side.
Would be greatfull if you could give me any more info on this joint is it easy to repair? could i get a seccond hand part fitted for it or [...]
This link might help you,if you are from canada you can go at canadian tire store and buy the honda civic repair book,i think it is around 25 $http://www.2carpros.com/makes/honda/civiā¦
In the 9th of May 2009, 1800AutoPart make over this site to be place where you can make a question where or how you should buy auto parts or parts replacement for your cars or motorcycles